Power over Gigabit Ethernet (PoGE)


Overview  

  • Delivers DC power in-line with the Array's Gigabit Ethernet connection
  • 3 units available: 1-port 60W, 1-port 80W, and 8-port 480W
  • Power Arrays remotely up to 100m over Category 5e or 6 cable

Value Delivered  

  • Provides simple, low cost means to remotely power Xirrus Arrays
  • Run a single cable for Data and Power
  • Lowers installation and maintenance cost

The Xirrus XP Power over Gigabit Ethernet (PoGE) system provides a simple, low cost means to remotely power Xirrus Arrays. The PoGE system delivers DC power in-line with the Array's Gigabit Ethernet data connection. This enables a single cable to deliver both data and power to Xirrus Arrays.

The Xirrus XP PoGE system consists of a midspan injector which typically resides in the wiring closet and a splitter which is collocated with the Array. The systems can provide up to 80W of 48VDC power over up to 100m of Category 5e or 6 cable.

PoGE System Architecture
       PoGE System Architecture

Key Features  

  • Up to 80W delivered power per connection
  • Fully compliant with IEEE 802.3af for detection, disconnect, and voltage control
  • Power Arrays remotely up to 100m over Category 5 or 6e cable
  • Compatible with 10/100/1000BASE-T Ethernet data connections
  • Built-in over current, over voltage, and short circuit protection
  • Diagnostic LEDs

PoGE System Architecture  

The XP PoGE system consists of two components:

  1. The mid-span injector that typically resides in the IT closet collocated with the data switches that provide wired network connectivity to the Arrays. The data connection coming out of the switch is connected to the injector. The injector then adds power to the cable. The Array is then connected to the output of the injector.
  2. A one-port splitter that is collocated with the Array. The splitter takes the connection from the mid-span injector and splits out power and data to the appropriate ports on the Array.

Product Information

Model NumberDescription
XP1-SPL • 1-port Power over Gigabit Ethernet Splitter
• Splits power and data at the Wi-Fi Array
• Supports XS4
XP1-MSI• 1-port Power over Gigabit Ethernet Midspan Injector
• Up to 60W DC power over Cat5e or Cat6 cabling
• One per Array
• Support XS4 and XS8
XP1-MSI-X • 1 port High Power over Gigabit Ethernet Midspan Injector
• Up to 80W DC power over Cat5e or Cat6 cabling
• One per Array
• Supports XS4, XS8, and XS16
XP8-MSI • 8-port Power over Gigabit Ethernet Midspan Injector
• Up to 80W DC power over Cat5e or Cat6 cabling
• One injector supports up to eight Arrays (up to eight XS4, eight XS8, or four XS16)

Product Specifications

 InjectorSplitter

Input

Voltage100-240VAC, 47-63Hz45-57 VDC
CurrentXP1-MSI: 1A(rms) max at 90VAC, 0.7A(rms) max at 240VAC

XP1-MSI-X: 1.25A(rms) max at 90VAC, 0.9A(rms) max at 240VAC

XP8-MSI: 9.0A(rms) max at 90VAC, 4.5A(rms) max at 240VAC		1.1A (RMS) max
Leakage CurrentXP1: 0.25mA max at 254 VAC 60Hz

XP8: 3.5mA max At 254 VAC – 60Hz		 
AC Inrush Current15A (RMS) max at 115VAC
20A (RMS) max at 230VAC		 

Output

Total PowerXP1-MSI: 60W
XP8-MSI: 480W (8 x 60W)
XP1-MSI-X: 80w		 
Output Voltage+56 VDC44-57V, 1.1A (48VDC nominal)
Load0.55A Max 
Regulation and RippleMeets IEEE 802.3afUnregulated
EfficiencyXP1: 65% (typical) at max load and 120VAC 60Hz
XP8: 75% (typical) at max load and 120VAC 60Hz		98% (typical) at max load and 53V input
Output Voltage ProtectionOutputs have short circuit and overload protection. May be shorted permanently without damage.Yes
Compliance1. CE
2. FCC Part 15 Class B
3. EN 55022 Class B 		1. CE
2. EN 55022 Class A
TemperatureOperational: 0 to +40°C
Non-operational: -25 to +65°C		Operational: 0 to +40°C
Non-operational: -20 to +65°C
Humidity5-90%5-90%
LocationThese products are intended for indoor usage only. Do not use them outdoors
DimensionsXP1-MSI-H
Length: 190mm (7.5 in)
Width: 80mm (3.15 in)
Height: 43.6mm (1.72 in)
Weight: 0.25kg (0.55 lb)

XP1-MSI-HX
Length: 203mm (8 in)
Width: 131mm (5.16 in)
Height: 63mm (2.48 in)
Weight: 1.75kg (3.86)

XP8-MSI-H
Length: 438mm (17.25 in)
Width: 228mm (8.98 in)
Height: 44.5mm (1.75 in)
Weight: 3.65kg (8.05 lb)

XP1-SPL-H
Length: 123mm (4.84in)
Width: 54mm (2.13in)
Height: 27mm (1.06in)
Weight: 0.1kg (0.22lb)		 
Power CordLength: 6 feetNA
IndicatorsLED #1 ON - Green: Input power on
LED #2 FAULT - Red: Fault
LED #3 CONNECT - Green: valid IEEE802.3af load detected/connected.		LED #1 OUTPUT - Green: Output good
ConnectorsAC Power: IEC320 inlet 3 pin
Input/Output Data: RJ45		DC Power: 3 pin Buchanan terminal block
Input/Output Data: RJ45
Ethernet CablingCat 5e or Cat 6. Total length of all cable runs from Ethernet switch to Array must be no more than 100m.

Product Ordering Information

Model Number Description
XP1-MSI 1 Port Power over Gigabit Ethernet Midspan Injector. Remotely powers one XS4 or XS8 Arrays. If using with the XS4, an XP1-SPL must be used at the Array.
XP1-MSI-X 1 Port Power over Gigabit Ethernet Midspan Injector. Remotely powers one XS4 or XS8C. If using with the XS4, an XP1-SPL must be used at the Array.
XP8-MSI 8 Port Power over Gigabit Ethernet Midspan Injector. Rack mountable, 1U chassis. Remotely powers up to eight XS4, eight XS8 or four XS16 Arrays. If using with the XS4, an XP1-SPL must be used at the Array.
XP1-SPL 1 Port Power over Gigabit Ethernet Splitter. Splits power from data cable at Array. Supports XS4 Array.